Introduction to the U5A target
The U5A eScore target is a next generation electronic target based on acoustic scoring. It works well with supersonic ammunition and is designed to be placed at 100-300 meter rifle ranges. The U target has all electronics and sensors placed at the bottom of the target, making it extremely robust when placed correctly (behind a berm or protective plates).
Features of the U5A target
- 3 acoustic sensors, all placed at the bottom of the target.
- Wide range of target faces and target definitions are available.
- Guide pin design allows swift change of target face, without need for additional zero point adjustment.
- Can be used with a wide range of supersonic calibers - from .223 to .338LM and more.
Technical specifications and dimensions
A |
1300 mm |
 |
B |
1300 mm |
|
C |
500 mm |
|
D |
300 mm |
|
E |
68 mm |
 |
F |
36 mm |
|
G |
92 mm |
|
H |
Max 164 mm |
| Temperature range | -30 to +60 °C |
| Weight | ~ 30 kg |
| Power consumption | ~ 4 W @ 24 VDC |
| Calibers | Supersonic projectiles |
Exploded view and parts list
| Item | Part name | KTS part no. |
| 1 | Target U5A - eScore | 13020313 |
| 3 | Main target rubber skin (2pcs pr target) | 97020540 |
| 6 | Fixation pin |
Treaded centre: 97020729 Non threaded centre: 97020850 |
| 7 | Front temperature shield |
Several available See table below |
| 8 | Foam sheet insert |
Several available See table below |
| 9 | Rear temperature shield | 13020103 |
| 10 | Target face |
Several available See table below |
| 11 | Fixation nut (8pcs pr target) | 97020729 |
| 14 | Male I/O cable |
Amphenol: 13020209 M23: 13020190 |
| 15 | Female I/O cable |
Amphenol: 13020210 M23: 13020191 |
| 16 | Horizontal rubber band |
97020895 (60cm wide) 97020547 (46cm wide) |
| 18 | Top cover | 97020527 - 130cm |
Front temperature shields available:
| Abbr. part name | KTS part no. | Target setup no. |
| P30A | 13020133 | #1 |
| P40A | 13020104 | #2 |
| P50A | 13020106 | #3 |
| P60A | 13020243 | #4 |
Foam sheet inserts available:
| Abbr. part name | KTS part no. | Fits target setup no. |
| FS 30x30/35x35 | 13020155 | #1 |
| FS 40x40/50x50 | 13020158 | #2 |
| FS 50x50/60x60 | 13020159 | #3 |
| FS 60x60/70x70 | 13020154 | #4 |
| FS 60x60/120x80 | 13020213 | #4 |
Target faces available:
| Abbr. part name | KTS part no. | Fits target setup no. | Fits target scoring definition no. |
| 13''/A | 13020081 | 1, 2, 3, 4 | 369 |
| 19''/A | 13020082 | 3, 4 | 370 |
| 6.35''/A | 13020130 | 1, 2, 3, 4 | 372 |
| 1/10/A | 13020226 | 1, 2, 3, 4 | 155 |
| C20/A | 13020227 | 1, 2, 3, 4 | 278 |
| C25/A | 13020228 | 1, 2, 3, 4 | 350 |
| 1/8/A | 13020229 | 2, 3, 4 | 348 |
| (10/30)/A | 13020230 | 1, 2, 3, 4 | 353 |
| (30/10)/A | 13020231 | 1, 2, 3, 4 | 277 |
| 1/3/A | 13020232 | 3, 4 | 38 |
| R20/A | 13020250 | 1, 2, 3, 4 | 7, 77, 169, 269 |
| R60/A | 13020251 | 4 | 3, 6, 21, 196, 217, 288, 295 |
| 8''/A | 13020277 | 1, 2, 3, 4 | 123, 378, 379, 384, 413 |
| 11 ¾'' /A | 13020278 | 1, 2, 3, 4 | 426 |
| 1/4/A | 13020280 | 2, 3, 4 | 39 |
| 1/4V/A | 13020281 | 2, 3, 4 | 429 |
| C30/A | 13020282 | 2, 3, 4 | 40 |
| 1/6/A | 13020283 | 4 | 279 |
| S25H/A | 13020284 | 4 w/13020213 | 351 |
| (13/40)/A | 13020285 | 2, 3, 4 | 276 |
| (40/13)/A | 13020286 | 2, 3, 4 | ??? |
| S25V/A | 13020287 | 4 w/13020213 | 356 |
| Småen/A | 13020297 | 1, 2, 3, 4 | 113 |
| IPSC V2/A | 13020298 | (*Note 2) | 440 |
| R24/A | 13020304 | 1, 2, 3, 4 | 1, 92 |
| R40/A | 13020305 | 2, 3, 4 | 2, 4, 170, 399 |
| B45/A | 13020319 | 2, 3, 4 | 354 |
| C40/A | 13020320 | 2, 3, 4 | 357 |
| Sirkel/A | 13020321 | 1, 2, 3, 4 | 79, ??? |
| Tønne/A | 13020322 | 1, 2, 3, 4 | 164 |
| Blank/A | 13020387 | 1, 2, 3, 4 | All (*Note1) |
| C15/A | 13020388 | 1, 2, 3, 4 | 156 |
| P-Fig/A | 13020397 | 1, 2, 3, 4 | ??? |
| D-Fig/A | 13020398 | 1, 2, 3, 4 | ??? |
| Fiskebeck/A | 13020416 | 4 w/13020213 | ??? |
| Mini P/A | 13020417 | 1, 2, 3, 4 | ??? |
| Mini 1/9/A | 13020418 | 1, 2, 3, 4 | ??? |
| Dråpe/A | 13020419 | 1, 2, 3, 4 | ??? |
| 1/9/A | 13020420 | 1, 2, 3, 4 | ??? |
Note1: This target face is all-white and may be fitted with any target figures by customer.
Note2: This target face is black. White spot is intended, by adding white contrast sheet (KTS part no: 14020409).
Disassembly
U target disassembly
...
Target maintenance
Rotating rubber band. Replacing foam sheet.
Horizontal rubber band explanation
The rubber at target is worn by penetrating projectiles. This will eventually cause noise to enter the soundproof measuring chamber inside the target. Such wear normally occurs in the center of the target. To ease maintenance and lower maintenance cost the target is fitted with a rubber band and a foam sheet insert that is covering the centre of the target.
This rubber band must cover the hole, pre-cut or later cut out, of the target rubber skin. The rubber band is intended to be rotated sideways to eliminate the wear at centre. When rubber band is rotatd, the foam sheet should also be replaced.
How often this maintenance is needed depends on calibres in use, bullet shapes, shooting distance and shooter skills (grouping). As a rule of thumb, for this target model, we recommend following intervals based on shooting distance:
| Shooting distance: | Maintenance intervals: |
| 100m/yds | Every 400 shots |
| 200m/yds | Every 1500 shots |
| 300m/yds | Every 3000 shots |
The rubber band need to be rotated approximately ½ of the diameter of the cut-out section of the main target rubberskin, if the rubber band isn't worn excessively. For a new target, this would be approcimately 20cm (8'').
When the rubber band eventually is rotated ½ roud, it needs to be replaced with a new one.
U-Target inspection
Repair ricochet damages to target rubber skin
In the event of projectiles passing through the target as they are tilted or otherwise deformed, they may generate large holes in the target rubber skins.
If the large holes occur in the X-rubber, scoring issues are prevented by exchanging it.
If the large holes occur at the main target rubber skin, outside the X-rubber, the holes need to be patched. This is done by spray glue and a piece of adhesive tape, or fast curing super glue and a piece of rubber.
Inspecting the target rubber skin
The target rubber skin need to be replaced in these events:
| 1. | Excess wear (large number of shot holes) at target rubber skin will affect scoring accuracy. This is especially important at the edge of the cut-out of the target rubber skin. This phenomena is particularly bad when the rubber sheet doesn't hold together, and coin sized parts start dangling. |
| 2. | As the target rubber skin is aging, its tensile strength will degrade. The target measuring chamber (between the target rubber skins) may eventually implode if the target is subjected to wind. Implosions can be temporarily be fixed by detaching, stretching and reattaching the target rubber skin. |
| 3. | As the target rubber skin is aging, it will eventually start to crack. Cracks may become holes and compromise the sound proof measuring chamber. |
Cleaning sensos
Rubber particles and debris will fall to the bottom of the target. Some will pile at the sensors.
It is recommended to clean the sensors at 3000 shots intervals, or before competitions. Cleaning is done with a soft brush, brushing off particles at the sensor heads.
Warning!
Do not use excess forse when brushing, thus dislocating the sensors.
Target service panel at the bottom of the target need to be opened to access the sensors (sensor bar). To open the service panel, FX target face and (lower) temperature shield first need to be removed from target. Also two rubber straps at the hatch need to be taken off. Please remember to put them back after cleaning.
Inspecting the target face
Target faces are worn by penetrating projectiles. They should be replaced if they provide a poor target profile for the shooter. Fixation nuts (at front of the target) must be taken off before replacing target face - if they are not attached with velcro (see parts list).
Inspecting the target service panel
The lower part of the target has a service panel that can be opened to access the target electronics and the lower sensors. Opening and closing is done by operting the white rubber straps at the bottom of the target.
Inspect the physical integrity of the service panel and its hinges/straps, and check that it's possible to close completely. There should be no cracks that sound can “leak” through when the service panel is closed. Always keep the service panel closed and strapped, expect when servicing or inspecting the internals of the target.
Target repairs
I/O cable repairs
Target I/O cables, at the bottom of the target, can easily be replaced when the front target service panel is opened. The I/O cables have connectors at both ends, one for connection to the scoring system, and one for connection to the target electronics inside the target.
I/O cables are lead through a track in the target frame, and put in a loop just inside the target frame. They are attached to the taget frame with duct tape, cable ties and cable clips. Make sure that the cable loop doesn't touch the nearby sensor.
Protection of the U5A target
How to protect the U5A target from stray bullets and ricochets
Protecting the eScore acoustic target
The eScore targets have the critical electronics located at the bottom of the tar
The targets have the most critical, or all, electronic components located at the bottom of the target - behind the service panel. To minimize maintenance cost and maintain the target durability it is recommended to protect this section of the target by use of a knee wall or protective plates. Target stands with protective plates are available on request.
Please refer to this YouTube video for recommendations on how to install the targets.
Protection from ricochets and shrapnel
Some shooting ranges have backstop that create shrapnel when bullets hit bullet catchers. This should be avoided since cables may be cut or short circuited by shrapnel or bullet jackets. To minimize the effects careful placement of the wiring between targets, antennas, batteries etc. must be done. If steel bullet catcher is used, make sure to cover it with rubber material or other absorbent material to minimize ricochets and shrapnel exiting the bullet catcher.